Marantz Model 30 Integrated Amplifier


The Marantz Model 30 integrated is a music lovers’ dream, continuing the renowned heritage of exquisite Marantz amplifiers and tuned by the Marantz Sound Master who channeled his passion, experience, and extraordinary ear into the design.


The Marantz Model 30 integrated amplifier continues the renowned heritage of exquisite Marantz amplifiers. Tuned by the Marantz Sound Master who channeled his passion, experience, and extraordinary ear into the amplifier design.
MODEL 30 is built on its own discrete circuit board, the Hyper-Dynamic Amplifier Module, or HDAM. By custom-curating hundreds of individual parts, rather than adopting an off-the-shelf solution, the MODEL 30 HDAM significantly outperforms standard integrated circuits to create the unique musicality you always expect from Marantz.
Envisioned to deliver optimal sound quality by simplifying the signal path – vital given the delicate nature of phono signals – the Phono EQ stage in the MODEL 30 amplifier can be used with both moving magnet and low-output moving coil cartridges, thanks to a built-in MC head amplifier. The design lowers distortion, which is why the phono stage uses two-stage amplification, combining Marantz HDAMs with JFETs in the input stage, giving high input impedance. This allows the non-negative-feedback design to be further simplified by the deletion of coupling capacitors, again reducing distortion and enhancing signal purity.
Rated Output Power 100W + 100W (8ohm)
200W + 200W (4ohm)
Amplifier Circuit Switching Amp
(Hypex NC500/SMPS600
by single)
Power Trans Toroidal w/case
Volume Electric
Loudness No
Bass / Treble / Mid / Balance Control yes / yes / No / yes
REC Out Select No
Source Direct yes
Pure Direct No
(Marantz) Purest Mode No
Isolator (for USB-B input) No
Jitter reducer No
Dual Clock: 44.1 / 48 kHz No
Digital Filter No
Analog Amp Mode No
Wide Range 5Hz – 50kHz
Total Harmonic Distortion 0.005%
(1kHz, 8Ω)
Damping Factor 500
Input Sensitivity: Phono input MM: 2.3 mV / 39 kohm
MC: 250
Input Sensitivity: CD/Line/Recorder 220 mV / 13 kohm
Input Sensitivity: Power Amplifier input 1.1 V / 13 kohm
SN Ratio PHONO (MM): 88dB
PHONO (MC): 75dB
CD: 107dB
Phono Input yes (MM/MC)
Ext. Pre Input (Power Amp Direct) yes
Preout yes
Audio (In/Out) Terminals

*except Power Amp Direct In(or Ext-Pre) and Pre-out

* [PHONO] and [CD] inputs = high grade terminals.
Balanced XLR input No
Rec-Out Selector No
Optical input No
Coaxial input No
2 sets of Spk Terminal No
Speaker Terminal Marantz Original
Remote Control Bus Terminal yes (Cinch)
Ethernet No
MC / MM phono input impedance selector
In order to optimize sound performance when using a moving coil (MC) or magnetic moving (MM) cartridge, and to accommodate all configurations as much as possible, MODEL 30 is equipped with an input impedance selector. The input impedance can be adjusted to three different settings: MC LOW (33 ohm), MC MID (100 ohm) and MC HIGH (390 ohm).
Analog-feel Volume Control
Newly developed electric volume control uses the latest volume control IC to realize better channel separation, dynamic range, and distortion-reduction. MODEL 30 employs a new Marantz-designed electric volume control for high linearity and best-in-class channel separation. In other words, you always get the volume precisely how you want it.
Fully Discrete Current Feedback Pre-Amplifier
Current Feedback pre-amplification with HDAM-SA3 is a well-known, Marantz-original circuit technology, thoughtfully designed to match the requirements of super audio High-Resolution music for wide-bandwidth and high-speed reproduction. Being fully discrete, each part can be individually selected and optimized for sound quality and performance by the Marantz Sound Master during long listening sessions.
Switching Power Amplification
MODEL 30 maintains the purest possible sound and supports the power needed to drive the most demanding speakers. The amplifier output stage of MODEL 30 allows a large power output, delivering 2x100W into an 8ohms load, and easily copes with low impedance speakers thanks to a 2x200W output into 4ohms. Because the feedback is taken after the output filter coil in this switching amplification design, the output frequency response stays the same and is not influenced by the impedance of the connected loudspeaker, ensuring the most musical sound no matter the loudspeakers. The amplifier module connects directly to the rear panel PCB on MODEL 30 to minimize the output path to maintain signal purity and sound stability.
Carefully selected components
Marantz has built a reputation for choosing the best possible components for its products. Extensive, loving tuning has long been the secret of fine-sounding Marantz amplifiers. Marantz engineers select and optimize each component through careful listening in dedicated Marantz facilities in Europe and Japan. During the development stage, every part is carefully selected, tested, and validated by the Marantz Sound Master to ensure you get that perfect Marantz sound every time you listen.
Two independent power supplies
MODEL 30 boasts two independent power supplies for the best separation between the pre-amplifier stages and power amplifier stage, where signal levels are still low and the audio signal is sensitive to any distortion, and the power amplifier stage, which drives the speakers with high signal levels and current. The MODEL 30 power supply circuit, designed exclusively for the preamplifier, enables a stable power supply that is not affected by fluctuations from power demanded by the power amplifier stage. An oversized toroidal transformer, known for its clean supply, is dedicated exclusively for the preamp to ensure high purity. A double shield steel case is mounted around the transformer to suppress the leakage flux that could affect peripheral circuits. The power supply for the power amplifier stage is designed to deliver high current instantaneously to the switching mode amplifier. This ensures full control over connected speakers to follow even the hardest bass attacks and provides clean power for the reproduction of the finest details.
Multiple Analog Inputs and Outputs
In addition to phono and CD analog inputs, MODEL 30 features two line-level inputs and one pair of recorder input/output jacks that enable the connection of multiple sources and recorders. Use MODEL 30 as a standalone stereo power amplifier for additional system configuration versatility with the included power amp direct input. For example, use the front pre-outs of your AV setup and run them through MODEL 30 power amps.


  • Output Power @ 8 Ohms: 100W + 100W
  • Output Power @ 4 Ohms: 200W + 200W
  • Amplifier Circuit: Hypex NC500/SMPS600
  • Frequency Range: 5Hz – 50kHz
  • Damping Factor: 500
  • SN Ratio: Phono (MM) 88dB, Phono (MC) 75dB, CD 107dB
  • Weight: 14.8kg

Additional information


Black, Silver